View U6043B-MY_1115182.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* * * * * *
Temperature and Supply Voltage Compensated Flashing Frequency Frequency Doubling Indicates Lamp Outage Relay Driver Output with High Current Carrying Capacity and Low Saturation Voltage Minimum Lamp Load for Flasher Operation: 1 W Very Low Susceptibility to EMI Protection According to ISO/TR 7637/1 Level 4
Flasher IC with 18-m Shunt U6043B
1. Description
The bipolar integrated circuit U6043B is used in relay-controlled automotive flashers where a high level EMC is required. Lamp outage is indicated by frequency doubling during hazard warning as well as direction mode.
Rev. 4726B-AUTO-11/05
2. Block Diagram
Figure 2-1. Car Flasher Application Circuit
+ VS + 49 6 C1 4 K1 Measuring comparator V 6 - 49 mV 20 k 5 k 7 2 R3 Shunt 18 m
K2 R1 Pulse generator 3 49 a-Comparator K 2 20 k 49 a-Comparator K 3 K3 5 20 k 23 V 5 k IC Ground 1 R4 470 5 W 21 W 21 W GND - 31 21 W 21 W 5 W 8 Relay R2 49 a 1.5...2.2 k
Indicator lamps
2
U6043B
4726B-AUTO-11/05
U6043B
3. Pin Configuration
Figure 3-1. Pinning
GND 1 2 8 7 SI
VS REL OSC
LD VS OSC
U6043B
3 4 6 5
Table 3-1.
Pin 1 2 3 4 5 6 7 8
Pin Description
Symbol GND VS REL OSC OSC VS LD SI Function IC ground Supply voltage Relay driver Oscillator Oscillator Supply voltage, Sense Lamp outage detection Start input (49a)
4. Functional Description
4.1 Pin 1, GND
The U6043B is protected against damage in case of battery reversal via resistor R4 to ground (-31). An integrated protection circuit together with external resistances R2 and R4 limits the current pulses in the IC.
4.2
Pin 2, Supply Voltage, VS power
The arrangement of the supply connections to Pin 2 (and 6) must be so as to ensure that on the connection printed circuit board (PCB), the resistance of VS to Pin 6 is lower than that to Pin 2.
4.3
Pin 3, Relay Control Output (Driver)
The relay control output is a high-side driver with a low saturation voltage. It is capable of driving a typical automotive relay with a minimum coil resistance of 60 .
3
4726B-AUTO-11/05
4.4
Pin 4 and 5, Oscillator
The flashing frequency, f1, is determined by the R1C1 components as given by the following formula below (see Figure 2-1):
1 ------------------------------------ Hz R 1 x C 1 x 1,5
1
where C1 47 F, R1 = 6.8 k to 510 k In case of a lamp outage (see Pin 7) the oscillator frequency is switched to the lamp outage frequency f2 with f2 2.2 x f1. Duty cycle in normal flashing mode: 50% Duty cycle in lamp outage mode: 40% (bright phase)
4.5
Pin 6, Supply Voltage, Sense
For accurate monitoring via the shunt resistor, a minimized layer resistance from point VS/shunt to Pin 6 is recommended.
4.6
Pin 7, Lamp Outage Detection
The lamp current is monitored via an external shunt resistor Rsh and an internal comparator K1 with its reference voltage of typically 49 mV (VS = 12 V). The outage of one lamp is detected according to the following calculation: Nominal current of 1 lamp: 21 W/(VS = 12 V): Ilamp = 1.75 A Nominal current of 2 lamps: 2 x 21 W/(VS = 12 V): Ilamp = 3.5 A We recommend setting the detection threshold in the middle of the current range: Ioutage 2.7 A Thus, the shunt resistor is calculated as: Rsh = VT (K1)/Ioutage Rsh = 49 mV/2.7 A = 18 m Comparator K1's reference voltage is matched to the characteristics of filament lamps (see "Control Signal Threshold" in the data part). The combination of shunt resistor and resistance of wire harness prevents Pin 7 from a too high voltage in case of shorted lamps.
4.7
Pin 8, Start Input
Start condition for flashing: the voltage at Pin 8 has to be below the K3 threshold (flasher switch closed). Humidity and dirt may decrease the resistance between 49 a and GND. If this leakage resistance is > 5 k, the IC is still kept in the off-condition. In this case the voltage at Pin 8 is between the thresholds of comparators K2 and K3. During the bright phase the voltage at Pin 8 is above the K2 threshold, during the dark phase it is below the K3 threshold. For proper start conditions a minimum lamp wattage of 1 W is required.
4
U6043B
4726B-AUTO-11/05
U6043B
5. Absolute Maximum Ratings
Reference point Pin 1
Parameters Supply voltage Surge Forward Current tP = 0.1 ms tP = 300 ms tP = 300 ms Output current Power Dissipation Tamb = 95 C Tamb = 60 C Junction temperature Ambient temperature range Storage temperature range DIP8 SO8 DIP8 SO8 Ptot Ptot Ptot Ptot TJ Tamb Tstg 420 340 690 560 150 -40 to +95 -55 to +150 mW mW mW mW C C C Pin 2 and 6 Pin 2 and 6 Pin 8 Pin 3 IFSM IFSM IFSM IO 1.5 1.0 50 0.3 A A mA A Pin 2 and 6 Symbol VS Value 16.5 Unit V
6. Thermal Resistance
Parameters Junction ambient DIP8 SO8 Symbol RthJA RthJA Value 110 160 Unit K/W K/W
7. Electrical Characteristics
Typical values under normal operation in application circuit (see Figure 2-1), VS (+49, Pin 2 and 6) = 12 V. Reference point ground (-31), Tamb = 25C, unless otherwise specified.
Parameters Supply voltage range Supply current Relay control output: Saturation voltage Reverse current Start delay (Delay time) Frequency tolerance Bright period Frequency increase Control signal threshold Leakage resistance Lamp load Test Conditions Pin 2 and 6 Dark phase, Pin 2 and 6 Bright phase, Pin 2 and 6 Pin 3 IO = 150 mA, VS= 9 V First bright phase Normal flashing Basic frequency f1 Control frequency f2 Lamp outage VS = 15 V, Pin 7 VS = 9 V, Pin 7 VS = 12 V, Pin 7 49a to GND Symbol VS IS IS VO IO ton f1 f1 f2 f2 VRs VRs VRs RP PL 1 -5 47 37 2.15 x f1 50 43 47 53 45 49 4 Min. 9 4.5 7.0 Typ. Max. 15 8 11 1.0 0.1 10 +5 53 45 2.3 x f1 57 47 51 5 Unit V mA mA V mA ms % % % Hz mV mV mV k W
5
4726B-AUTO-11/05
8. Ordering Information
Extended Type Number U6043B-MY U6043B-MFPY U6043B-MFPG3Y Package DIP8 SO8 SO8 Remarks Pb-free Tubed, Pb-free Taped and reeled, Pb-free
9. Package Information
6
U6043B
4726B-AUTO-11/05
U6043B
Package SO8
Dimensions in mm
5.00 4.85 1.4 0.4 1.27 3.81 8 5 0.25 0.10 0.2 3.8 6.15 5.85 5.2 4.8 3.7
technical drawings according to DIN specifications
1
4
10. Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4726B-AUTO-11/05 History * Put datasheet in a new template * First page: Pb-free logo added * Page 6: Ordering Information changed
7
4726B-AUTO-11/05
Atmel Corporation
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600
Atmel Operations
Memory
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759
Regional Headquarters
Europe
Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500
Microcontrollers
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60
Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom
Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80
Asia
Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743
Japan
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
(c) Atmel Corporation 2005. All rights reserved. Atmel (R), logo and combinations thereof, Everywhere You Are (R) and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
4726B-AUTO-11/05

▲Up To Search▲

Price & Availability of U6043B-MY

	To Download U6043B-MY Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .